[English version] [zur deutschen Version]

Laser setup

The laser source of the LASER4DIY project is a diode pumped solid state laser with a Neodymium-doped yttrium orthovanadate (Nd:YVO4) crystal. This widely-used laser is especially suitable for this usecase, since the Nd:YVO4 cristal is cheap, easy to obtain and also, based on the use of the so called bounce geometry, very powerful. In figure 1 you can see the setup of the laser system, which is very similar to the puplication by Thomas and Damzen, 2011 [1]

Figure 1: Schematic representation of the Nd:YVO4 laser with a passive Q-switch
and a Cr4+:YAG saturable absorber crystal and a additional KTP crystal for frequency doubling [1]

The measurements of the trapezoid Nd:YVO4 crystal are 15 x 5 x 2mm. To avoid a parasitic internal reflection in the crystal, the end planes are tilted inwardes by 4 degrees and also are anti reflection coated for the wavelength of 1064nm. The cylindric laser diode array emits a wavelength of 808nm with maximum optical power of P = 60W with a efficiency rate of 50%. With a vertical cylindric lens (VCLD) the pump light is focused with a focus length of 10mm into the crystal. The Nd:YVO4 crystal emits light at λ= 1064nm and converts some of the energy into heat. Because of this and the fact, that the laser diode shifts its wavelength about 1nm per 3K temperature change away from the for the Nd:YVO4 optimal pump wavelength of 808nm, the laserdiode and the crystal need cooling to keep them at a steady temperature. This is done by copper plates which are mounted on both side of the crystal, which themselves are cooled by a peltier element and CPU coolers.

...

Figure 3: Scematic view of the beam path with bounce geometry (left)
and beam path adapted for simulation (right)  

Figure 4: Temperature distribution for side pumped crystal

Figure 5: Temperature distribution for simulated crystal

...

In figure 5 the average output power of the laser beam in CW mode is shown as a function of the absorbed pumping power. The reflecivity of the uncoupling mirror was set to R=0.9. The beam power approximately increases linearly to the absorbed pumping power up to 35W and then turn into an exponential function up to a pumping power of 51W, where the maximum output power of 24W is reached. Thus, a effiency of about 50% is achieved. Thomas and Damzen, 2011 reached an output power of 13.8W (with R=0.7) and efficiency of only 30%.

Figure 6: Simulated average output power of the laser beam as a function
of the absorbed pumping power; CW mode with R=0.9

Additionally, a simulation with Q switch was performed (figure 7). Here, too, a linear dependency of average output power and absorbed pumping power can be observed, as in CW mode. This simulation resulted in an output power of 17W at a maximum pumping power of 51W. Compared to Thomas and Damzen, 2011, where an output power of 11W at R=0.7 was measured, this computed value is much higher. The cause of this is the lack of a real bounce geometry in the simulation. A lower output power needs to be expected in reality, therefore, as in CW mode.

Figure 7: Simulated average output power of the laser beam as a function
of the absorbed pumping power; with Q switch and R=0.9

The simulation was also used to calculate the average output power as a function of the reflecitity ouf the output mirror. Figure 8 shows a power reduction with increasing reflectifity. Taking the results of Thomas and Damzen, 2011 in consideration, here we can expect a less intense reduction of the power in experimental test runs, too. 

Abbildung 8: Simulated average output power of the laser beam as a function
of the output mirror reflectivity with a pumping power of 51W

...

Figure 9 shows a peak power of 16kW with a pulse length of 9.39ns. Taking account the appoximate factor for the bounce geometry, in this simulation also results in a significantly higher peak power of Ps ≈ 24kW compared to Thomas und Damzen, 2011, where a peak power of 1.9kW was measured in experiments.

Figure 9: Simulated peak power as a function of pulse length with a output mirrow
reflectivity of 0.9 and a pumping power of 51W

The results of the performed simulations show much higher output power figures than to be expected regarding the experiments done by Thomas und Damzen, 2011. Nevertheless the results can serve as a starting point for the setup of the mirrors when building the resonator. Additionally, the simulation showed, that the used setup of the laser with a Nd:YVO4 crystal can provide enough power for the ablation of copper.

Construction

In the ongoing work package we plan the construction of the laser source, including the heat sinks to dissipate surplus heat.

[Work in progress]

Conclusion

The results from the simulation performed generally showed significantly higher output powers than could be expected under real conditions according to [1]. In an experiment, we have shown that this setup works in principle and is also suitable for generating laser pulses with peak powers that are sufficiently high for the ablation of copper, even if the values ​​from the simulation – as expected – could not be achieved.

However, practical weaknesses of the setup were also identified:

• A high output power of the pump diode is decisive for the output power of the laser. The use of 60W diodes was planned. However, the procurement of these diodes turned out to be difficult. Tested specimens could not meet the specifications. In order not to unnecessarily delay the progress of the project, a laser diode from a premium supplier was used for further tests. The diode can meet the requirements, but its price exceeds the targeted material costs.
• The use of weaker pump diodes causes a lower output power and jeopardizes the achievement of the project goal, namely the possibility of copper ablation.
• An auxiliary laser is required to adjust the laser structure; we used an Nd:Yag laser. However, the cost of this laser drives up the cost and adjusting the setup is complicated. This reduces the attractiveness of the project.

For these reasons, we looked for an alternative setup that on the one hand increases the possible peak performance and on the other hand makes it easier to adjust the system. The resulting setup is described here. 

...

Literature:

[1]    G. M. Thomas and M. J. Damzen, “Passively Q-switched Nd: YVO 4 laser with greater than 11W average power,” Opt. Express, vol. 19, no. 5, pp. 4577–4582, 2011.
[2]    “Betrieb von Lasereinrichtungen,” Berufsgenossenschaft der Feinmechanik und Elektrotechnik, Berufsgenossenschaftliche Informationen für Sicherheit und Gesundheit bei der Arbe 832, 2003.

...